Wholesale Pure Moly Sheet Molybdenum Metal Plate And Mu Metal Sheet
To create far more benefit for customers is our company philosophy; customer growing is our working chase for Wholesale Pure Moly Sheet Molybdenum Metal Plate And Mu Metal Sheet, Warmly welcome to cooperate and create with us! we’re going to continue to provide merchandise with high-quality and competitive rate.
To create far more benefit for customers is our company philosophy; customer growing is our working chase for 99.95% Molybdenum Sheet, Molybdenum Sheet, Many products fully conform to the most rigorous of international guidelines and with our first-rate delivery service you will have them delivered at any time and in any place. And because Kayo deals in the entire spectrum of protective equipment, our customers don’t need to waste time shopping around.
Molybdenum Sheet
1.Thickness and width tolerances
Cold rolled sheets
| Thickness(mm) | Thickness tolerance(±mm) | Max.width(mm) | Width tolerance(±mm) |
| 0.10 | 0.008 | 305 | 0.5 |
| 0.10-0.127 | 0.010 | 305 | 0.5 |
| 0.127-0.15 | 0.010 | 610 | 0.5 |
| 0.15-0.25 | 0.015 | 800 | 0.5 |
| 0.25-0.50 | 0.020 | 915 | 1.6 |
| 0.50-0.80 | 0.028 | 915 | 1.6 |
| 0.80-1.20 | 0.035 | 915 | 1.6 |
| 1.20-2.00 | 3% | 915 | 1.6 |
Cold rooled sheets
| Thickness(mm) | Thickness tolerance(±mm) | Max.width(mm) | Width tolerance(±mm) |
| 1.00 | 0.080 | 850 | 2.0 |
| 1.00-1.50 | 0.130 | 850 | 2.0 |
| 1.50-2.00 | 0.150 | 850 | 2.0 |
| 2.00-3.60 | 0.180 | 1200 | 2.0 |
| 3.60-50.00 | 5% | 1500 | 2.0 |
Length tolerace:
The length tolerace for sheet length up to 2500 mm is max. +5/-0 mm.
The length tolerance of sheet cuts can vary with a total tolerance range not exceeding the above given value. The maximum sheet dimensions depend on the sheet thickness.other dimensions upon request.
Sheet with premium surface condition are available from 0.15 to 1 mm.Sheet with thickness from 0.127 to 0.381 mm can be delivered as coils upon request.(production length max.10500mm)
Flatness:
Max.1% for sheet thickness≥0.3mm
Max.4% for sheet thickness＜0.3mm
(measuring proedure on the basis of ASTM B386)
2. Physical and mechanical product properties.
Density: ≥10.2g/cm³
Vickers Hardness:
≤1.0mm: 240-280 HV
1.00-3.60mm: 240-270 HV
306-10.00mm: 220-270 HV
10.00-50.00: ＞200 HV
Tensile test:
| Thickness(mm) | Tensile Srenght Min. (MPa) | 0.2 % Yield strength Min. (MPa) | ElongationMin.(%) |
| 0.1-0.25 | 700 | 620 | 2.0 |
| 0.25-0.40 | 680 | 590 | 3.0 |
| 0.40-0.65 | 680 | 590 | 5.0 |
| 0.65-1.50 | 680 | 580 | 10.0 |
| 1.50-2.30 | 640 | 580 | 12.0 |
| 2.30-5.00 | 640 | 580 | 15.0 |
| 5.00-10.00 | 640 | 580 | 10.0 |
| 10.00-13.00 | 590 | 540 | 10.0 |
| 13.00-25.00 | 500 | 480 | 2.0 |
| 25.00-50.00 | 500 | 480 | 1.0 |
Surface condition
Appearance: The material will be of uniform quality, free from foreign matter, splits and fractures. bed sheet(not trimmed) may have small edge cracks.
Surface defects are assessed in the frame of visual inspection.
Local surface defects can be removed by frinding within the specified thickness tolerace.
Surface condition: Cold rolled, bright(≤1mm) Ra≤0.20μm
Cold rolled, pickled: Ra≤1.00μm
Cold rolled ground: Ra≤0.60μm
Chemical composition:
| Main and minor components | Min.content(%) | ASTM B386 (361) |
| Mo | 99.97 | balance |
| Impurities | Max.values (μg/g) | Max.values (μg/g) |
| Al | 10 | - |
| Cu | 20 | - |
| Cr | 20 | - |
| Fe | 20 | 100 |
| K | 20 | - |
| Ni | 10 | 50 |
| Si | 20 | 100 |
| W | 300 | - |
| C | 30 | 100 |
| H | 10 | 20 |
| N | 10 | 70 |
| O | 40 | - |
| Cd | 5 | - |
| Hg | 1 | - |
| Pb | 5 | - |
