Manufacturing Companies for Purity Molybdenum Sheet/plate
We have been also concentrating on enhancing the things management and QC method so that we could preserve terrific edge inside the fiercely-competitive enterprise for Manufacturing Companies for Purity Molybdenum Sheet/plate, We welcome new and previous customers from all walks of lifestyle to call us for upcoming business enterprise interactions and reach mutual accomplishment!
We have been also concentrating on enhancing the things management and QC method so that we could preserve terrific edge inside the fiercely-competitive enterprise for Molybdenum Sheet/Plate, Purity Molybdenum Plate, Purity Molybdenum Sheet, All these products are manufactured in our factory located in China. So we can guarantee our quality seriously and availably. Within these four years we sell not only our products but also our service to clients throughout the world.
Molybdenum Sheet
1.Thickness and width tolerances
Cold rolled sheets
| Thickness(mm) | Thickness tolerance(±mm) | Max.width(mm) | Width tolerance(±mm) |
| 0.10 | 0.008 | 305 | 0.5 |
| 0.10-0.127 | 0.010 | 305 | 0.5 |
| 0.127-0.15 | 0.010 | 610 | 0.5 |
| 0.15-0.25 | 0.015 | 800 | 0.5 |
| 0.25-0.50 | 0.020 | 915 | 1.6 |
| 0.50-0.80 | 0.028 | 915 | 1.6 |
| 0.80-1.20 | 0.035 | 915 | 1.6 |
| 1.20-2.00 | 3% | 915 | 1.6 |
Cold rooled sheets
| Thickness(mm) | Thickness tolerance(±mm) | Max.width(mm) | Width tolerance(±mm) |
| 1.00 | 0.080 | 850 | 2.0 |
| 1.00-1.50 | 0.130 | 850 | 2.0 |
| 1.50-2.00 | 0.150 | 850 | 2.0 |
| 2.00-3.60 | 0.180 | 1200 | 2.0 |
| 3.60-50.00 | 5% | 1500 | 2.0 |
Length tolerace:
The length tolerace for sheet length up to 2500 mm is max. +5/-0 mm.
The length tolerance of sheet cuts can vary with a total tolerance range not exceeding the above given value. The maximum sheet dimensions depend on the sheet thickness.other dimensions upon request.
Sheet with premium surface condition are available from 0.15 to 1 mm.Sheet with thickness from 0.127 to 0.381 mm can be delivered as coils upon request.(production length max.10500mm)
Flatness:
Max.1% for sheet thickness≥0.3mm
Max.4% for sheet thickness＜0.3mm
(measuring proedure on the basis of ASTM B386)
2. Physical and mechanical product properties.
Density: ≥10.2g/cm³
Vickers Hardness:
≤1.0mm: 240-280 HV
1.00-3.60mm: 240-270 HV
306-10.00mm: 220-270 HV
10.00-50.00: ＞200 HV
Tensile test:
| Thickness(mm) | Tensile Srenght Min. (MPa) | 0.2 % Yield strength Min. (MPa) | ElongationMin.(%) |
| 0.1-0.25 | 700 | 620 | 2.0 |
| 0.25-0.40 | 680 | 590 | 3.0 |
| 0.40-0.65 | 680 | 590 | 5.0 |
| 0.65-1.50 | 680 | 580 | 10.0 |
| 1.50-2.30 | 640 | 580 | 12.0 |
| 2.30-5.00 | 640 | 580 | 15.0 |
| 5.00-10.00 | 640 | 580 | 10.0 |
| 10.00-13.00 | 590 | 540 | 10.0 |
| 13.00-25.00 | 500 | 480 | 2.0 |
| 25.00-50.00 | 500 | 480 | 1.0 |
Surface condition
Appearance: The material will be of uniform quality, free from foreign matter, splits and fractures. bed sheet(not trimmed) may have small edge cracks.
Surface defects are assessed in the frame of visual inspection.
Local surface defects can be removed by frinding within the specified thickness tolerace.
Surface condition: Cold rolled, bright(≤1mm) Ra≤0.20μm
Cold rolled, pickled: Ra≤1.00μm
Cold rolled ground: Ra≤0.60μm
Chemical composition:
| Main and minor components | Min.content(%) | ASTM B386 (361) |
| Mo | 99.97 | balance |
| Impurities | Max.values (μg/g) | Max.values (μg/g) |
| Al | 10 | - |
| Cu | 20 | - |
| Cr | 20 | - |
| Fe | 20 | 100 |
| K | 20 | - |
| Ni | 10 | 50 |
| Si | 20 | 100 |
| W | 300 | - |
| C | 30 | 100 |
| H | 10 | 20 |
| N | 10 | 70 |
| O | 40 | - |
| Cd | 5 | - |
| Hg | 1 | - |
| Pb | 5 | - |
