IOS Certificate Purity Mo1 Molybdenum Plate And Sheet
With this motto in mind, we’ve got become among essentially the most technologically innovative, cost-efficient, and price-competitive manufacturers for IOS Certificate Purity Mo1 Molybdenum Plate And Sheet, Sincerely hope we’re increasing up along with our buyers all around the entire world.
With this motto in mind, we’ve got become among essentially the most technologically innovative, cost-efficient, and price-competitive manufacturers for Mo1, Molybdenum Plate, Molybdenum Plate And Sheet, In order to make more people know our merchandise and to enlarge our market, we’ve devoted a lot of attention to technical innovations and improvement, as well as replacement of equipment. Last but not the least, we also pay more attention to training our managerial personnel, technicians and workers in planned way.
Molybdenum Sheet
1.Thickness and width tolerances
Cold rolled sheets
| Thickness(mm) | Thickness tolerance(±mm) | Max.width(mm) | Width tolerance(±mm) |
| 0.10 | 0.008 | 305 | 0.5 |
| 0.10-0.127 | 0.010 | 305 | 0.5 |
| 0.127-0.15 | 0.010 | 610 | 0.5 |
| 0.15-0.25 | 0.015 | 800 | 0.5 |
| 0.25-0.50 | 0.020 | 915 | 1.6 |
| 0.50-0.80 | 0.028 | 915 | 1.6 |
| 0.80-1.20 | 0.035 | 915 | 1.6 |
| 1.20-2.00 | 3% | 915 | 1.6 |
Cold rooled sheets
| Thickness(mm) | Thickness tolerance(±mm) | Max.width(mm) | Width tolerance(±mm) |
| 1.00 | 0.080 | 850 | 2.0 |
| 1.00-1.50 | 0.130 | 850 | 2.0 |
| 1.50-2.00 | 0.150 | 850 | 2.0 |
| 2.00-3.60 | 0.180 | 1200 | 2.0 |
| 3.60-50.00 | 5% | 1500 | 2.0 |
Length tolerace:
The length tolerace for sheet length up to 2500 mm is max. +5/-0 mm.
The length tolerance of sheet cuts can vary with a total tolerance range not exceeding the above given value. The maximum sheet dimensions depend on the sheet thickness.other dimensions upon request.
Sheet with premium surface condition are available from 0.15 to 1 mm.Sheet with thickness from 0.127 to 0.381 mm can be delivered as coils upon request.(production length max.10500mm)
Flatness:
Max.1% for sheet thickness≥0.3mm
Max.4% for sheet thickness＜0.3mm
(measuring proedure on the basis of ASTM B386)
2. Physical and mechanical product properties.
Density: ≥10.2g/cm³
Vickers Hardness:
≤1.0mm: 240-280 HV
1.00-3.60mm: 240-270 HV
306-10.00mm: 220-270 HV
10.00-50.00: ＞200 HV
Tensile test:
| Thickness(mm) | Tensile Srenght Min. (MPa) | 0.2 % Yield strength Min. (MPa) | ElongationMin.(%) |
| 0.1-0.25 | 700 | 620 | 2.0 |
| 0.25-0.40 | 680 | 590 | 3.0 |
| 0.40-0.65 | 680 | 590 | 5.0 |
| 0.65-1.50 | 680 | 580 | 10.0 |
| 1.50-2.30 | 640 | 580 | 12.0 |
| 2.30-5.00 | 640 | 580 | 15.0 |
| 5.00-10.00 | 640 | 580 | 10.0 |
| 10.00-13.00 | 590 | 540 | 10.0 |
| 13.00-25.00 | 500 | 480 | 2.0 |
| 25.00-50.00 | 500 | 480 | 1.0 |
Surface condition
Appearance: The material will be of uniform quality, free from foreign matter, splits and fractures. bed sheet(not trimmed) may have small edge cracks.
Surface defects are assessed in the frame of visual inspection.
Local surface defects can be removed by frinding within the specified thickness tolerace.
Surface condition: Cold rolled, bright(≤1mm) Ra≤0.20μm
Cold rolled, pickled: Ra≤1.00μm
Cold rolled ground: Ra≤0.60μm
Chemical composition:
| Main and minor components | Min.content(%) | ASTM B386 (361) |
| Mo | 99.97 | balance |
| Impurities | Max.values (μg/g) | Max.values (μg/g) |
| Al | 10 | - |
| Cu | 20 | - |
| Cr | 20 | - |
| Fe | 20 | 100 |
| K | 20 | - |
| Ni | 10 | 50 |
| Si | 20 | 100 |
| W | 300 | - |
| C | 30 | 100 |
| H | 10 | 20 |
| N | 10 | 70 |
| O | 40 | - |
| Cd | 5 | - |
| Hg | 1 | - |
| Pb | 5 | - |
