Factory For Tzm Moly Molybdenum Alloy Dies,Sheets,Rods,Bars,Plates,Boats,Crucibles
We thinks what customers think, the urgency of urgency to act in the interests of a customer position of principle, allowing for better quality, lower processing costs, prices are more reasonable, won the new and old customers the support and affirmation for Factory For Tzm Moly Molybdenum Alloy Dies,Sheets,Rods,Bars,Plates,Boats,Crucibles, Because we stay within this line about 10 years. We got very best suppliers aid on quality and cost. And we had weed out suppliers with poor high-quality. Now lots of OEM factories cooperated with us too.
We thinks what customers think, the urgency of urgency to act in the interests of a customer position of principle, allowing for better quality, lower processing costs, prices are more reasonable, won the new and old customers the support and affirmation for Tzm Alloy For Aerospace Electronics And Thermal Treatment, Tzm Alloy For Isothermal Forging, Tzm Alloy For Vacuum Industry Frunace, With a wide range, good quality, reasonable prices and stylish designs, our products are extensively used in public placesand other industries. Our products are widely recognized and trusted by users and can meet continuously developing economic and social needs. We welcome new and old customers from all walks of life to contact us for future business relationships and achieving mutual success!
TZM rods
Chemical composition:
| Main and minor components | Min.content(%) | ASTM B386 (361) |
| Mo | blance | balance |
| Ti | 0.40-0.55% | 0.40-0.55% |
| Zr | 0.06-0.12% | 0.06-0.12% |
| Impurities | Max.values (μg/g) | Max.values (μg/g) |
| Al | 10 | - |
| Cu | 20 | - |
| Cr | 20 | - |
| Fe | 20 | 100 |
| K | 20 | - |
| Ni | 10 | 50 |
| Si | 20 | 50 |
| W | 300 | - |
| C | 100-400 | 100-400 |
| H | 10 | - |
| N | 10 | 20 |
| O | 500 | 300 |
| Cd | 5 | - |
| Hg | 1 | - |
| Pb | 5 | - |
Dimensions and tolerances:
| Diameter (mm) | Diameter tolerance (mm) |
| Ground | |
| 0.50-0.99 | ±0.007 |
| 1.00-1.99 | ±0.010 |
| 1.00-2.99 | ±0.015 |
| 3.00-15.9 | ±0.020 |
| 16.0-24.9 | ±0.030 |
| 25.0-34.9 | ±0.050 |
| 35.0-3939 | ±0.060 |
| ≥40.0 | ±0.20 |
| Cleaned | |
| 0.50-4.0 | ±2.0% |
| 4.10-10.0 | ±1.5% |
| 15.0-50.0 | ±0.30 |
| 51.0-75.0 | ±0.40 |
| 75.1-120.0 | ±1.00 |
| 121.0-165.0 | ±1.50 |
| Turned | |
| 40.0-49.9 | ±0.30 |
| 50.0-165.0 | ±0.40 |
Length and straightness:
| Diameter (mm) | Production length (mm) | Stiraightness/Meter (mm) | |
| Cleaned | Ground/turned | ||
| 0.50-0.99 | ＞500 | ＜2.5 | ＜2.5 |
| 1.00-9.90 | ＞300 | ＜2.0 | ＜1.5 |
| 10.0-165.0 | ＞100 | ＜1.5 | ＜1.0 |
Length tolerance:
| Diameter 0.50-30.0 mm | ||||||
| Nominal length (mm) | 6-30 | 30-120 | 120-400 | 400-1000 | 1000-2000 | ＞2000 |
| Length tolerance(mm) | ±0.2 | ±0.3 | ±0.5 | ±0.8 | ±1.2 | ±2.0 |
| Diameter ＞30.0 mm | ||||||
| Nominal length (mm) | 6-30 | 30-120 | 120-400 | 400-1000 | 1000-2000 | ＞2000 |
| Length tolerance(mm) | ±1.0 | ±1.5 | ±2.5 | ±4.0 | ±6.0 | ±8.0 |
Density:
1. 0.50-40.0 mm ≥10.15g/cm³
2. 40.1-80.0 mm ≥10.10g/cm³
3. 80.1-120.0 mm ≥10.00g/cm³
4. 120.1-165.0 mm ≥9.90g/cm³
Nondestructive testing: For diameters＞15.00 mm:100% ultrasonic testing; For diameters of 0.50-50.0mm:Eddy curent tests on rods with ground.
| Diameter(mm) | Tensile strength(MPa) | 0.2% Yield Strength(MPa) | Elongation(%) | Hardness(HV 10) |
| 0.50-4.76 | - | - | - | - |
| 4.76-22.20 | ≥790 | ≥690 | ≥18 | |
| 22.20-28.60 | ≥760 | ≥655 | ≥15 | 260-320 |
| 28.60-47.60 | ≥690 | ≥585 | ≥10 | 250-310 |
| 47.60-73.00 | ≥620 | ≥550 | ≥10 | 245-300 |
| 73.00-120.9 | ≥585 | ≥515 | ≥5 | 240-290 |
| 121.0-165 | ≥585 | ≥515 | ≥5 | 220-280 |
Surface condition:
| Surface： | Cleaned | Ground | Turned |
| φ0.50-165mm | φ0.50-50.00mm | φ≥40.00mm | |
| Roughness | Diameter (mm) | Ra (μm) Ground | Ra (μm) Turned |
| ≤2.50 | ≤0.80 | - | |
| 2.5-50.0 | ≤1.00 | - | |
| ≥40.0 | - | ≤3.2 |
